Every part
we'd run on our own decks.

Spacers 10mm/0,4" width (x1)

Longboard Skateboard spacers Ideal to adjust the wheel pulley distance Ideal between bearings Width: 10mm

Longboard Washers (10x Black)

Very helpful   washers to get the right clearance between pulleys and mounts, for motor pulleys too (with seeger) 8mm int.  diameter 1mm thick Kit of 10 pcs

Peel-N-Stick Polyester Velcro 10cm/4" (tailored)

Strong adhesive velcro for electronics Easily fasten electronics to the Deck or Enclosure Pack of 2pcs male/female Width: 10cm/4″ Lenght: 10cm/4″ (tailored)

Electric mountainboard Aluminium Valve Cap (set of 4)

Sensors adapter JST 1.5mm to 2.0mm female 6 pins

Vesc sensors adapter 1.5mm jst 6 pins female to 2.00 jst 6 pins female

Bluetooth UART module for electric skateboards (Android Ackmaniac ONLY)

This will send motors, batteries, vescs data to your Smartphone using ANDROID app trought Bluetooth 7 pin JST wire assembled Tested before shipping Plug & Play Covered with heatshrink It works with Ackmaniac installed into the Vesc/Focbox Made in Italy Tested, heatshrinked (black) and labeled before shipping

M4 bolts for enclosures (6 pairs or more)

Standard kit of 6 + 6 pcs 6 M4 Black bolt 16mm length 6 M4 thread screws for wood with hexagonal head 10mm length Pay attention to make the holes deep enough to let fit the silver wood screws perfectly, otherwise you may force the hexagonal head (specially with bad tools). We suggest to use these washers for decks with 10-11mm thickness to get more clearance and avoiding to completely pass through the deck.

XT90 Nylon Connectors

XT60 Nylon Connectors

Anti-spark power switch (Fully Assembled)

CUSTOMIZED/PLUG & PLAY 4 oz PCB Safe for batteries up to 12S 12AWG in/out wires included based on fuse Amperage + led switch wires and connections diagram included 40 to 100amps fuses XT60 or XT90 connectors (optional) Detachable Led switch in different colours (optional) 20cm switch wires

Soft rounded black gasket for motor and sensor wires (5pcs)

5 pcs of black soft rounded gaskets Max 6mm inneri diameter The tight gasket hold perfectly 5.5mm connectors with heatshrink They require 10mm holes Max panel mount thickness: 3mm

Insulation paper 8 x 50 cm (1x sheet)

1 sheet of 8,00 x 50cm High quality insulating sheet Useful to insulate the sides of battery packs

Vital Longboard & Skateboard tool

5.5mm Male Gold Connectors (3pcs)

5.5mm Female Gold Connectors (3pcs)

Electric Mountain Board Bearings (set of 8)

  9,5 mm x 22mm fit with all terrain/flywheels & 9.5mm axle trucks 9,5 mm x 28mm fit with 8inch tires & 9.5mm axle trucks 12 mm x 28mm fit with 8inch tires & 12mm axle trucks For Caliber II trucks and all terrain just buy standard 8 x 22mm bearings ( like this )

CAN bus Connector for Electric skateboard Speed controllers

Can bus cable to connect 2 esc for electric skateboards Needed for Dual Drive

2 x Seeger for 8mm shaft

Seeger for 8mm shaft Set of 2 pcs

Dc IN Battery 2.1mm Socket with Dust cover

The Dust cover will be Clear (not Black) 2.1x 5.5mm DC Socket Max 4A Max 10mm Shaft length Max panel dept 3mm It require a 12mm hole on the enclosure

Waterproof Cover for On Off BMS Switch 20mm

Waterproof Dustproof cover for on off switch 20mm  

Big On Off BMS Switch

0/1 Switch On Off Switch 6A – 250 V Max panel dept 3mm It require a 20mm hole on the enclosure Can be waterproof if mounted with this cover

Led Switch for Antispark (self locking 5 pins)

Colored Led switch 3A 250VAC Max panel dept 5mm Different colors It require a 16mm hole on the enclosure

2.50" Bolts - 60mm (set of 8)

Extra Long 2,5 inches bolts (60mm) INOX bolts BLACK nuts Pack of 8 pieces

1.75" Bolts - 44mm (set of 8)

Extra Long 1,75 inches bolts (44mm) With 8 nuts Pack of 8 pieces

Black Silicon glue for power packs

Strong and professional black silicon glue (neutral) The best way to securly fasten the batteries to the enclosure Clean result

Braided Cable Sleeving 1m (various size - tailored)

Diameter:  6mm or 10mm before expansion Length: tailored 1 unit = 1 meter

Soft black gasket for Enclosures perimeters 1m (tailored)

Soft waterproof high quality gasket Width: 10Mm Height 7.5mm It won’t get damaged by drilling holes Nice to get the right clearances in curvy decks

Heat Shrink Tubing 10cm/4" (various size - tailored)

Diameters: 3-4-5-6-10-12-15-30-50mm before expansion Length: tailored in multiple of 10cm Few diameters in different colors 1 unit = 10 cm

Wrist string for remote

Black Wrist string for remotes

Heat shrink for Esk8 Lithium Battery Packs 1m (various size - tailored)

Width:  180mm or 223mm Length: tailored Colors: black, yellow and blue 1 unit = 1 meter

10 & 12 AWG silicone wires in Black/Red 10cm (various size - tailored)

  Size:  10AWG or 12AWG Length: tailored (max 10m length per roll) Colors: BLACK or RED 1 unit = 10 centimeters

Eskating UART Custom JST PH Connector 2.0mm 7 pins

Custom JST PH 2.0mm 7 pins Connector 4 wires only: 5V – GND – TX – RX Ready to solder to any UART BT module Length: 15cm

Pre cutted Pure Nickel 0.15mm 10mm (various size - tailored)

Pre-cutted  Nichel strips ready to go! Width:  10mm Thickness: 0.15mm Length: tailored (max 10m per roll if 1 meter is selected) Quantity: 100x 3cm or 10x 5/6,8cm or 1x meter The 30mm strips are normally used for 2xcells parallel connections and all serial connection with 2 cells distance on most of batteries to be fold or with 2 flats The 50mm strips are normally used for 3xcells parallel connections The 68mm strips are normally used for 4xcells parallel connections Need any other size? please tell us , we can cut from 0.1mm to 9999mm length 😉 1 unit = 100 X 30mm or 10 X 50mm/ 70mm or 1 meter each unit

Insulation paper Positive (1x sheet of 40pcs)

1 sheet of 4*10 = 40 pieces High quality Perfect fit for 18650 cells  

40 to 100amp fuses

Compact T Tool by Lazyrolling

The compact t-tool features a small, simple and functional design perfect to bring for the everyday ride It is a must for all skateboard owners to have a skate tool, whether the board is electric or not As images show it’s a compact design, simple to carry and to store.

12mm Aluminium Washers (5x)

Very helpful   washers to get the right clearance between pulleys and mounts 12mm int.  diameter 19mm ext. diameter 1mm thick Kit of 5 pcs

Pre cutted Pure Nickel 0.15mm 25mm (1m)

New 25mm wide Nichel strip! Width: 25mm Thickness: 0.15mm Length: tailored (max 10m per roll if 1 meter is selected) Quantity: multiple of 1 meter Need any other size? please tell us , we can cut from 0.1mm to 9999mm length 😉 1 unit = 1 meter

Battery Percentage/Voltage BLUE LCD Display Waterproof (if glued)

Include +- 20cm wire Battert percentage and voltage Blue led color Up to 12s 60x32x15mm

Battery Percentage LCD Display (various colors)

Include 20cm wire Battery percentage display It needs an on off switch (like antispark switch) or another kind of switch, otherwise it will stays always on Blue, Green 3s-15s 60x23x15

Spacers 10mm/0,4" width (x1)

Longboard Skateboard spacers Ideal to adjust the wheel pulley distance Ideal between bearings Width: 10mm

All terrain Longboard wheels 100mm RED (set of 4)

Unstoppable All Terrain Wheels Fit with  standard 22mm bearings Ideal with Caliber Trucks 78a Duro Colors: Red Diameter: 100mm Compatible with the All Terrain Wheel Pulleys

Longboard Washers (10x Black)

Very helpful   washers to get the right clearance between pulleys and mounts, for motor pulleys too (with seeger) 8mm int.  diameter 1mm thick Kit of 10 pcs

Electric mountainboard Aluminium Valve Cap (set of 4)

Eskating PRO Wheels 73A 97mm

AWESOME PRICE High quality PU electric skateboard wheels Highest rebound Diameter: 97 mm Width 52mm 73a duro Colors: Black and white Logo Set of 4 Wheels Compatible with the Abec 11 Wheel Pulleys

Electric Mountain Board 8" Inner Tube (1pc)

  Diameter: 8 inches (20cm)

Electric Mountain Board Bearings (set of 8)

  9,5 mm x 22mm fit with all terrain/flywheels & 9.5mm axle trucks 9,5 mm x 28mm fit with 8inch tires & 9.5mm axle trucks 12 mm x 28mm fit with 8inch tires & 12mm axle trucks For Caliber II trucks and all terrain just buy standard 8 x 22mm bearings ( like this )

12mm Aluminium Washers (5x)

Very helpful   washers to get the right clearance between pulleys and mounts 12mm int.  diameter 19mm ext. diameter 1mm thick Kit of 5 pcs

REVERSE Esk8 motor mount "Aluminium Carbon PRO"

Reverse model with the motors mounted backward Strong clamp and perfect aligment for any 50-63 motor Made in Italy Easy to install (the clamp has just 1 bolt) Fit with our 16/38 pulleys and 325mm belt Adjustable length and angle For Genuine   Caliber II Trucks ONLY (other calibers v1 or clones might be sanded to fit these mounts)

Electric skateboard motor mount "Aluminium Carbon PRO"

Strong clamp and perfect aligment for any 50-63 motor Made in Italy Easy to install (the clamp has just 1 bolt) Fit with our 15/36 pulleys and 265mm belt Fit with our 15/42 pulleys and 280mm belt Adjustable length and angle For Genuine   Caliber II Trucks ONLY (other calibers v1 or clones might be sanded to fit these mounts)

Dual Kit Electric Mountainboard Motor Mounts with Brakets

Big Sale on Limited Stock! 2x Aluminium Clamps and 2x Carbon Fiber Motor Plates Dual Mounts Kit for ATS 12 Trucks 2 x Protection Brackets included Easy to install (the clamp has just 1 bolt) Wide clamp and perfect aligment Fit with 50-63mm motors Fit with our 15/72 pulleys and 475mm belt Fit with our 18/42 pulleys and 400mm belt Adjustable length and angle Made in Italy Please note: the kit include the full hardware needed, brackets and motor mounts ( motors and trucks not included)

HTD 5M 72 Teeth Nylon Carbon Pulley for MBS fivestar & rockstar Hubs

Nylon Carbon Fiber fivestar & rockstar MBS hubs pulleys by Eskating Theet: 72 For 15mm belts Include 5 x M4 BLACK 50mm bolts for Rockstar or 60mm bolts for Fivestar hubs 3d Printed in Italy

Electric Mountain Board ATS 12 12mm/4,7" Trucks MBS (1x)

  Axle diameter: 12mm/4.7″

Electric mountainboard Aluminium Valve Cap (set of 4)

Dual Kit Electric Mountainboard Motor Mounts with Brakets

Big Sale on Limited Stock! 2x Aluminium Clamps and 2x Carbon Fiber Motor Plates Dual Mounts Kit for ATS 12 Trucks 2 x Protection Brackets included Easy to install (the clamp has just 1 bolt) Wide clamp and perfect aligment Fit with 50-63mm motors Fit with our 15/72 pulleys and 475mm belt Fit with our 18/42 pulleys and 400mm belt Adjustable length and angle Made in Italy Please note: the kit include the full hardware needed, brackets and motor mounts ( motors and trucks not included)

Electric Mountain Board 8" Inner Tube (1pc)

  Diameter: 8 inches (20cm)

Electric Mountain Board Bearings (set of 8)

  9,5 mm x 22mm fit with all terrain/flywheels & 9.5mm axle trucks 9,5 mm x 28mm fit with 8inch tires & 9.5mm axle trucks 12 mm x 28mm fit with 8inch tires & 12mm axle trucks For Caliber II trucks and all terrain just buy standard 8 x 22mm bearings ( like this )

HTD 5M 95 teeth Belt 475mm for Mountainboards Mounts

High quality Electric skateboard Belt Lenght: 475mm Teeth: 95 Fit with 15/72 pulleys and Eskating Mountainboard motor mounts Width: 15mm Glass Fibre reinforced Material: neopropene rubber

HTD 5M 72 Teeth Nylon Carbon Pulley for TRAMPA Superstar wheels

Nylon Carbon Fiber Superstar Trampa hubs pulleys by Eskating Theet: 72 For 15mm belts Include 5 x M4 BLACK 50mm bolts 3d Printed in Italy

HTD 5M 80 teeth Belt 400mm for Mountainboards Mounts

High quality Electric skateboard Belt Lenght: 400mm Teeth: 80 Fit with 18/42 pulleys and Eskating Mountainboard motor mounts Width: 15mm Glass Fibre reinforced Material: neopropene rubber

12mm Aluminium Washers (5x)

Very helpful   washers to get the right clearance between pulleys and mounts 12mm int.  diameter 19mm ext. diameter 1mm thick Kit of 5 pcs

HTD 5M 72 Teeth Nylon Carbon Pulley for MBS fivestar & rockstar Hubs

Nylon Carbon Fiber fivestar & rockstar MBS hubs pulleys by Eskating Theet: 72 For 15mm belts Include 5 x M4 BLACK 50mm bolts for Rockstar or 60mm bolts for Fivestar hubs 3d Printed in Italy

HTD 5M 36/38/40/42 Teeth Nylon Carbon KEGEL Wheel Pulley

Nylon Carbon Fiber  Wheel Pulley by Eskating Theet: 36/38/40/42 Width: 9, 12 or 15mm Include 6 x M5 BLACK bolts and 6 x M5 BLACK self locking nuts 3d Printed in Italy

Eskating Pulleys and Belts Cover for electric skateboards

New belt and pulley cover by Eskating 3d printed in Italy with high quality ABS and high resolution Hand refined through a special process that increase the strenght Rear Left and Rear right mount available (not symmetric because of the logo) Fully compatible with our Eskating Motor mounts Fully compatible with 15/36T and 265mm belt Available for 83, 90, 97/100mm or 107mm wheels

Custom HTD 5M 12 to 20 Teeth Steel Motor Pulley in 9/12/15 width

Eskating Custom Steel  Motor Pulleys Bore: 6mm, 8mm or 10mm Teeth: 12, 14, 15, 16, 18 or 20T Width: 9 (not for 12 and 15T), 12 or 15mm M4  tool included 2xM4 flat set screws ( Thread locker recommended ) Seegers and whashers recommended too IMPORTANT: 12T pulleys with a bore diameter of 10mm cannot fit the set screws.

HTD 5M 36/38/40/42 Teeth Nylon Carbon ALL TERRAIN Wheel Pulley

Nylon Carbon Fiber  Wheel Pulley by Eskating Theet: 36, 38,40 or 42 Width: 9, 12 or 15mm Include 6 x M5 BLACK boltsm and 6 x M5 BLACK self locking nuts 3d Printed in Italy

HTD 5M 36/38/40/42 Teeth Nylon Carbon ABEC 11 CLONES Wheel Pulley

Nylon Carbon Fiber  Wheel Pulley by Eskating For the Abec11 Flywheels CLONES ONLY Theet: 36/38/40/42 Width: 9, 12 or 15mm Include 6 x M5 BLACK bolts and 6 x M5 BLACK self locking nuts 3d Printed in Italy

2 x Seeger for 8mm shaft

Seeger for 8mm shaft Set of 2 pcs

HTD 5M 72 Teeth Nylon Carbon Pulley for TRAMPA Superstar wheels

Nylon Carbon Fiber Superstar Trampa hubs pulleys by Eskating Theet: 72 For 15mm belts Include 5 x M4 BLACK 50mm bolts 3d Printed in Italy

Eskating Pulleys and Belts Covers for electric skateboards (2x)

New belt and pulley cover by Eskating SPECIAL BUNDLE price for 2x pulley and belt covers 3d printed in Italy with high quality ABS and high resolution Hand refined through a special process that increase the strenght Rear Left and Rear right mount available (not symmetric because of the logo) Fully compatible with our Eskating Motor mounts Fully compatible with 15/36T and 265mm belt Available for 83, 90, 97/100mm or 107mm wheels

HTD 5M 36/38/40/42 Teeth Nylon Carbon ABEC 11 GENUINE FLYWHEEL/REFLY Wheel Pulley

Nylon Carbon Fiber  Wheel Pulley by Eskating For the Genuine ABEC 11 Flywheel & Refly  Theet: 36, 38,40 or 42 Width: 9, 12 or 15mm Include 6 x M5 BLACK boltsm and 6 x M5 BLACK self locking nuts 3d Printed in Italy

Electric Mountain Board ATS 12 12mm/4,7" Trucks MBS (1x)

  Axle diameter: 12mm/4.7″

Longboard Washers (10x Black)

Very helpful   washers to get the right clearance between pulleys and mounts, for motor pulleys too (with seeger) 8mm int.  diameter 1mm thick Kit of 10 pcs

2.50" Bolts - 60mm (set of 8)

Extra Long 2,5 inches bolts (60mm) INOX bolts BLACK nuts Pack of 8 pieces

1.75" Bolts - 44mm (set of 8)

Extra Long 1,75 inches bolts (44mm) With 8 nuts Pack of 8 pieces

12mm Aluminium Washers (5x)

Very helpful   washers to get the right clearance between pulleys and mounts 12mm int.  diameter 19mm ext. diameter 1mm thick Kit of 5 pcs

7s BESTECH bms 60a

HIGH QUALITY BMS by Bestech Protection Circuit Board for 25,9V 7S 60A Li-ion and Li-polymer battery pack Prevention of the battery pack from overcharge, overdischarge, over current, over temperature, short circuit With cell balance/equilibrium function With E-Swtich Charging and discharge at same port Instructions & Datasheet downloadable below

10s BESTECH bms 40a

HIGH QUALITY BMS by Bestech Protection Circuit Board for 37V 10S 40A Li-ion and Li-polymer battery pack Prevention of the battery pack from overcharge, overdischarge, over current, over temperature, short circuit With cell balance/equilibrium function With E-Swtich Charging and discharge at same port Instructions & Datasheet downloadable below

10s DALY bms Charge Only

HIGH QUALITY BMS by Daly Charge Only Protection Circuit Board for 36V 10S Li-ion and Li-polymer battery pack Prevention of the battery pack from overcharge, over temperature, short circuit 10A Max. Charge current 42V Max. Charge Voltage  (for 10s 36v Lithium Batteries) With cell balance/equilibrium function Size: 59 x 34 x 9mm  

12s DALY bms Charge Only

HIGH QUALITY BMS by Daly Charge Only Protection Circuit Board for 43V 12S Li-ion and Li-polymer battery pack Prevention of the battery pack from overcharge, over temperature, short circuit 10A Max. Charge current 50.4V Max. Charge Voltage  (for 12s 43v Lithium Batteries) With cell balance/equilibrium function Size: 63 x 50 x 12mm  

Eskating PRO motors 6374 190Kv

The kind of motor that makes the difference on your Esk8 High quality Electric skateboard Sealed & Sensored PRO motors Sensored with 6 pin 1,5mm JST wire (1,5 to 2,0mm jst 6 pin Adapter included) 5.5mm Gold Connectors Max. power:  3550W Shaft: 8mm With 2 x Circlips ways (8mm Circlips not included available here ) With Eskating Logo

Sensors adapter JST 1.5mm to 2.0mm female 6 pins

Vesc sensors adapter 1.5mm jst 6 pins female to 2.00 jst 6 pins female

Soft rounded black gasket for motor and sensor wires (5pcs)

5 pcs of black soft rounded gaskets Max 6mm inneri diameter The tight gasket hold perfectly 5.5mm connectors with heatshrink They require 10mm holes Max panel mount thickness: 3mm

2 x Seeger for 8mm shaft

Seeger for 8mm shaft Set of 2 pcs

Braided Cable Sleeving 1m (various size - tailored)

Diameter:  6mm or 10mm before expansion Length: tailored 1 unit = 1 meter

HTD 5M 56 teeth Belt 280mm (1x)

High quality Electric skateboard Belt Lenght: 280mm Teeth: 56 Fit with 15/42 pulleys and Eskating motor mounts Width: 15mm Glass Fibre reinforced Material: neopropene rubber

HTD 5M 53 teeth Belt 265mm (1x)

High quality Electric skateboard Belt Lenght: 265mm Teeth: 53 Fit with 15/36 pulleys and Eskating motor mounts Width: 9, 12 or 15mm Glass Fibre reinforced Material: neopropene rubber

HTD 5M 95 teeth Belt 475mm for Mountainboards Mounts

High quality Electric skateboard Belt Lenght: 475mm Teeth: 95 Fit with 15/72 pulleys and Eskating Mountainboard motor mounts Width: 15mm Glass Fibre reinforced Material: neopropene rubber

HTD 5M 80 teeth Belt 400mm for Mountainboards Mounts

High quality Electric skateboard Belt Lenght: 400mm Teeth: 80 Fit with 18/42 pulleys and Eskating Mountainboard motor mounts Width: 15mm Glass Fibre reinforced Material: neopropene rubber

HTD 5M 65 teeth Belt 325mm (1x)

High quality Electric skateboard Belt Lenght: 325mm Teeth: 65 Fit with 16/38 pulleys and Eskating REVERSE motor mounts Width: 15mm Glass Fibre reinforced Material: neopropene rubber

Sensors adapter JST 1.5mm to 2.0mm female 6 pins

Vesc sensors adapter 1.5mm jst 6 pins female to 2.00 jst 6 pins female

Bluetooth UART module for electric skateboards (Android Ackmaniac ONLY)

This will send motors, batteries, vescs data to your Smartphone using ANDROID app trought Bluetooth 7 pin JST wire assembled Tested before shipping Plug & Play Covered with heatshrink It works with Ackmaniac installed into the Vesc/Focbox Made in Italy Tested, heatshrinked (black) and labeled before shipping

Soft rounded black gasket for motor and sensor wires (5pcs)

5 pcs of black soft rounded gaskets Max 6mm inneri diameter The tight gasket hold perfectly 5.5mm connectors with heatshrink They require 10mm holes Max panel mount thickness: 3mm

CAN bus Connector for Electric skateboard Speed controllers

Can bus cable to connect 2 esc for electric skateboards Needed for Dual Drive

Landyachtz Dinghy Gin & Tonic 28.5"

Boxy Kicktail! The Little beast deck! Length:  28.5″ Width:  8.5″ Wheelbase:  15″ Concave Style:  Low Plys:  7 Construction:  Canadian Maple Flex Level:  Stiff

Black Jessup Griptape 100cm

10″ Wide grip tape (25,4cm) Length : 100cm

YOC Griptape Various Designs

YOC grip tape made in France 30cmx100cm grip tape Various designs Thickness of 1mm  Thickness of 3mm with foam , soft grip

Clear Jessup Griptape 100cm

10″ Wide grip tape (25,4cm) Length : 100cm For 100cm add 10x to cart

Landyachtz Evo Falcon 36"

Length:  36″ Width:  9.5″ Wheelbase:  27.75″ Concave Style:  Deep cave Plys:  10 Construction:  Maple Flex Level:  Stiff

Esk8 skateboard longboard Nose & Tail guard different colors (pair)

Main material is EPDM (Ethylene Propylene Diene Monomer), not ordinary rubber, more durable wear. Built-in high-strength border Installation does not require drilling, no additional tools (such as screwdriver), no glue, only 4 steps to complete the installation Colors: Red, Black, Orange and White Size: 12in/30cm, suitable for mostly every skateboard & Longboard Red, Black and White fit up to 15mm thick decks Orange model is for decks up to 10mm thickness

Fast Charger (10s and 12 s)

Fast charger 3.5a for 10s and 4 amp for 12s For 10 or 12s batteries ONLY (42v or 50.4v) Dc plug 5.5mm x 2.1mm Eu plug for 10s and Schuko for 12s Whitout FAN (silent)

Anti-spark power switch (Fully Assembled)

CUSTOMIZED/PLUG & PLAY 4 oz PCB Safe for batteries up to 12S 12AWG in/out wires included based on fuse Amperage + led switch wires and connections diagram included 40 to 100amps fuses XT60 or XT90 connectors (optional) Detachable Led switch in different colours (optional) 20cm switch wires

Dc IN Battery 2.1mm Socket with Dust cover

The Dust cover will be Clear (not Black) 2.1x 5.5mm DC Socket Max 4A Max 10mm Shaft length Max panel dept 3mm It require a 12mm hole on the enclosure

Waterproof Cover for On Off BMS Switch 20mm

Waterproof Dustproof cover for on off switch 20mm  

Big On Off BMS Switch

0/1 Switch On Off Switch 6A – 250 V Max panel dept 3mm It require a 20mm hole on the enclosure Can be waterproof if mounted with this cover

Led Switch for Antispark (self locking 5 pins)

Colored Led switch 3A 250VAC Max panel dept 5mm Different colors It require a 16mm hole on the enclosure

Battery Percentage/Voltage BLUE LCD Display Waterproof (if glued)

Include +- 20cm wire Battert percentage and voltage Blue led color Up to 12s 60x32x15mm

Battery Percentage LCD Display (various colors)

Include 20cm wire Battery percentage display It needs an on off switch (like antispark switch) or another kind of switch, otherwise it will stays always on Blue, Green 3s-15s 60x23x15

Bluetooth UART module for electric skateboards (Android Ackmaniac ONLY)

This will send motors, batteries, vescs data to your Smartphone using ANDROID app trought Bluetooth 7 pin JST wire assembled Tested before shipping Plug & Play Covered with heatshrink It works with Ackmaniac installed into the Vesc/Focbox Made in Italy Tested, heatshrinked (black) and labeled before shipping

Eskating UART Custom JST PH Connector 2.0mm 7 pins

Custom JST PH 2.0mm 7 pins Connector 4 wires only: 5V – GND – TX – RX Ready to solder to any UART BT module Length: 15cm

M4 bolts for enclosures (6 pairs or more)

Standard kit of 6 + 6 pcs 6 M4 Black bolt 16mm length 6 M4 thread screws for wood with hexagonal head 10mm length Pay attention to make the holes deep enough to let fit the silver wood screws perfectly, otherwise you may force the hexagonal head (specially with bad tools). We suggest to use these washers for decks with 10-11mm thickness to get more clearance and avoiding to completely pass through the deck.

Soft rounded black gasket for motor and sensor wires (5pcs)

5 pcs of black soft rounded gaskets Max 6mm inneri diameter The tight gasket hold perfectly 5.5mm connectors with heatshrink They require 10mm holes Max panel mount thickness: 3mm

ABS Enclosure 38x165x320mm

Vacuum formed Black Pinseal ABS case Enough space for 10s2p   Eskating 18650 battery, BMS on top and 2 esc (or up to 3 lipos, bms and 2 esc) Waterproof gasket of 10mm height included Thickness: 3mm Internal max size: 38mmx165mmx320mm (1,5″x6″x 12,5″) External max size:  41mmx215mmx370mm (1,6″x8,5″x 14,5″) Variable height thanks to the Gasket (+2 to 5 mm of internal height available) Screws not included (available here) Carefully Made in Italy

ABS Enclosure 38x165x530mm

NEW WATERPROOF GASKET (check the gallery) Vacuum formed  Black Pinseal ABS case Used on the  Dual Beast Evo Enough space for 10s4p/12s5p   Eskating 18650 battery, BMS, accessories and 2 esc/focboxes (or up to 5 lipos, bms and 2 esc) Waterproof gasket of 10mm height included Thickness: 3mm Internal max size: 38mmx165mmx520mm (1,5″x6″x 20,5″) External max size:  41mmx215mmx570mm  (1,6″x8″x 22,5″) Variable height thanks to the Gasket (+2 to 5 mm of internal height available) Screws not included (available here) Carefully Made in Italy

ABS Enclosure 38x160x200mm

NEW WATERPROOF GASKET (check the gallery) Vacuum formed Black Pinseal ABS case Enough space for 2 lipos , little BMS and 1 esc Waterproof gasket of 10mm height included Thickness: 3mm Internal max size: 38mmx160mmx200mm External max size:  41mmx210mmx250mm Variable height thanks to the Gasket (+2 to 5 mm of internal height available)ù Screws not included (available here) Blank (no holes) Carefully Made in Italy

ABS Enclosure 38x160x250mm

NEW WATERPROOF GASKET (check the gallery) Vacuum formed Black Pinseal ABS case Used on the Little Beast  Enough space for 2 lipos , little BMS and 2 esc Waterproof gasket of 10mm height included Thickness: 3mm Internal max size: 38mmx160mmx250mm (1,5″x6″x8″) External max size:  41mmx210mmx300mm (1,6″x8″x12″) Variable height thanks to the Gasket (+2 to 5 mm of internal height available) Screws not included (available here) Blank (no holes) Carefully Made in Italy

ABS Enclosure 38x165x420mm

NEW WATERPROOF GASKET (check the gallery) Vacuum formed  Black Pinseal ABS case Enough space for 10s4p   Eskating 18650 battery, BMS on top and 2 esc (or up to 4 lipos, bms and 2 esc) Waterproof gasket of 10mm height included Thickness: 3mm Internal max size: 38mmx165mmx420mm (1,5″x6″x 16,5″) External max size:  41mmx215mmx470mm  (1,6″x8″x 18,5″) Variable height thanks to the Gasket (+2 to 5 mm of internal height available) Screws not included (available here) Carefully Made in Italy

Soft black gasket for Enclosures perimeters 1m (tailored)

Soft waterproof high quality gasket Width: 10Mm Height 7.5mm It won’t get damaged by drilling holes Nice to get the right clearances in curvy decks

ABS SLIM Enclosure 24x150x500mm

NEW SLIM ENCLOSURE WATERPROOF GASKET INCLUDED Vacuum formed  Black Pinseal ABS case Used on the Single Beast Falcon Evo Enough space for a flat 10s4p with little bms in front and 2 max vesc/focboxes + accessories, or for the flat 10s3p Eskating battery with 60A bms in front + accessories and max 2 vesc/focboxes Waterproof gasket of 10mm height included Thickness: 3mm Internal size for almost of the space: 24mmx150mmx500mm (0.95″x5.9″x 19,68″) Internal height on top with overhang: 32mm (1.26″) External max size:  35mmx200mmx540mm  (1,38″x7.87″x 21.26″) Variable height thanks to the Gasket (+2 to 5 mm of internal height available) Screws not included (available here) Carefully Made in Italy New pictures updates coming soon

Anti-spark power switch (Fully Assembled)

CUSTOMIZED/PLUG & PLAY 4 oz PCB Safe for batteries up to 12S 12AWG in/out wires included based on fuse Amperage + led switch wires and connections diagram included 40 to 100amps fuses XT60 or XT90 connectors (optional) Detachable Led switch in different colours (optional) 20cm switch wires

Big On Off BMS Switch

0/1 Switch On Off Switch 6A – 250 V Max panel dept 3mm It require a 20mm hole on the enclosure Can be waterproof if mounted with this cover

Led Switch for Antispark (self locking 5 pins)

Colored Led switch 3A 250VAC Max panel dept 5mm Different colors It require a 16mm hole on the enclosure

Insulation paper 8 x 50 cm (1x sheet)

1 sheet of 8,00 x 50cm High quality insulating sheet Useful to insulate the sides of battery packs

Insulation paper Positive (1x sheet of 40pcs)

1 sheet of 4*10 = 40 pieces High quality Perfect fit for 18650 cells  

Maytech Remote

1 channel Receiver included Very nice signal with optimal control for acceleration and brakes Ergonomic grip 2 acceleration/brakes modes (2 settings from receiver, Basic and Pro) 3.7v Battery charged by USB 420mah and cable (included) Wrist strip included for FREE

Wrist string for remote

Black Wrist string for remotes

Riser with wires guide for Single/Dual Motor

Electric skateboard wires guide riser For Single or Dual Motor build Black strong ABS Height: 7mm

Angled HARD riser pads for electric skateboards 3°

Electric skateboard Angled riser pads (2pcs) ANGLED 8-14MM (3º) Does not include bolts and nuts ( available here)

Flat HARD riser pads for electric skateboards

Electric skateboard Flat riser pads (2pcs) Thickness: 5/16″ (8mm) Does not include bolts and nuts ( available here)

Pre cutted Pure Nickel 0.15mm 10mm (various size - tailored)

Pre-cutted  Nichel strips ready to go! Width:  10mm Thickness: 0.15mm Length: tailored (max 10m per roll if 1 meter is selected) Quantity: 100x 3cm or 10x 5/6,8cm or 1x meter The 30mm strips are normally used for 2xcells parallel connections and all serial connection with 2 cells distance on most of batteries to be fold or with 2 flats The 50mm strips are normally used for 3xcells parallel connections The 68mm strips are normally used for 4xcells parallel connections Need any other size? please tell us , we can cut from 0.1mm to 9999mm length 😉 1 unit = 100 X 30mm or 10 X 50mm/ 70mm or 1 meter each unit

Pre cutted Pure Nickel 0.15mm 25mm (1m)

New 25mm wide Nichel strip! Width: 25mm Thickness: 0.15mm Length: tailored (max 10m per roll if 1 meter is selected) Quantity: multiple of 1 meter Need any other size? please tell us , we can cut from 0.1mm to 9999mm length 😉 1 unit = 1 meter

Triple 8 Helmet Brainsaver Sweatsaver Certified

Well combinable with the Eskating Mask Dual Certified: Complies with U.S. CPSC Bike and ASTM Skate safety standards Includes 2 sets of Sweatsaver liners to customize fit Color: Matte Black Size: S/M 53 – 57 cm (21 – 22.5 in) | L/XL 57 – 60 cm (22.5 – 23.5 in)

Triple 8 KP Pro Knee Pads

Color: Matte Black S  32 – 36 cm (12.6 – 14.2 in) M  36 – 40 cm (14.2 – 15.7 in) L  40 – 44 cm (15.7 – 17.3 in) XL  44 – 50 cm (17.3 – 19.6 in)

Triple 8 EP55 Elbow Pads

Color: Matte Black S  15.2 – 20.3 cm (6 – 8 in) M  20.3 – 25.4 cm (8 – 10 in) L  25.4 – 30.5 cm (10 – 12 in) XL  30.5 – 35.6 cm (12 – 14 in)

Triple 8 Hired Hands

Color: Matte Black S  19 – 20 cm (7.5 – 7.9 in) M  20 – 23 cm (7.9 – 9 in) L  23 – 26 cm (9 – 10 in) XL  26 – 29 cm (10 – 11 in)